![]() |
|
|
||||||||
|
Home | Forums | Register | Gallery | FAQ | Calendar |
Retailers |
Community
![]() |
News/Info
![]() |
International Retailers
![]() |
IRC | Today's Posts |
![]() |
|
Thread Tools
![]() |
![]() |
#1 |
Banned
|
TM Hi-Capa 4.3 Metal Slide + Barrel Installation?
Anyone know how to install a Metal Slide + Metal Barrel Upgrade for the Tokyo Marui HI-Capa 4.3?
I just ordered one from an ASC member and hopefully it arrives tomrrow. I need some help installing it, unless someone can guide me through or show me some pictures on how to install it. If anyone can help me let me know, -Identity. |
![]() |
![]() |
![]() |
#2 |
when you pull down the hammer do u see a allen key type of screw in the midle below your sight if it does i think it should be the same as a 5.1 slide install
|
|
![]() |
![]() |
![]() |
#3 |
It’s not too hard to figure out how to install the slide. Just go slow and make sure to check your manual frequently. It should have a pretty good diagram of the assembly. You may have some trouble removing the outer barrel though. It was a little confusing for me as I did not want to use force. You just have to bend the plastic a bit and the inner barrel and hop up should just pop out for you.
I tried to find some instructions or tutorials online, but I could not find any for the Hi-Capa, though you may have better luck then me. Hope it goes well. |
|
![]() |
![]() |
![]() |
#4 |
Banned
|
Great stuff, after trying to fix up my Hi-Capa which still has problems I kinda figure out how to disassemble it.
|
![]() |
![]() |
![]() |
#5 |
Banned
|
Alright I got the metal slide, I took off the allen screw on the back of the hammer on the slide, now I dont know where to continue. The whole part doesnt seem to move...
|
![]() |
![]() |
![]() |
#6 |
![]() ![]() ![]() Join Date: Feb 2005
Location: Swimming in a pool of Xpresspost receipts.... Toronto - 400/401
|
Use some force to bend the two sides of the plastic slide away from each other, while wiggling the block out. Careful a spring might come flying out. Might wanna put your paintball goggles on
![]() |
![]() |
![]() |
![]() |
#7 | |
Banned
|
Quote:
I left the plastic barrel on and tested the slide, the only thing is that the slidelock kinda gets stuck and you have to push the slide and wiggle it around for the slidelock to fit in. If anyone knows how to put the metal barrel on let me know! :salute: Thanks. |
|
![]() |
![]() |
![]() |
#8 |
btw what brand did you get??
pm me...i live at shep and warden if you want i can give you some help....i have a creation on my 4.3 heavy bitch too..
__________________
![]() ![]() ![]() ![]() |
|
![]() |
![]() |
![]() |
#9 |
Banned
|
Right on, however deadaim isnt available till like 9:15pm... Does anyone else here know how to fit the hopup + barrel on the gun?
|
![]() |
![]() |
![]() |
#10 |
NAAZ's #1 fan!
|
yeah, its a simple twist. Counter clockwise if i remember right...(i know it doesnt look like it was ever ment to be taken out!)
|
![]() |
![]() |
![]() |
#11 | |
Banned
|
Quote:
Not take it out. |
|
![]() |
![]() |
![]() |
#12 |
Banned
|
Anyone? Any suggestions?
|
![]() |
![]() |
![]() |
#13 |
i'll let you know wen i get a day off...if you still have a problem...
__________________
![]() ![]() ![]() ![]() |
|
![]() |
![]() |
![]() |
#14 | |
Banned
|
Quote:
|
|
![]() |
![]() |
![]() |
#15 |
If the front sight is metal. You can use alittle heat to melt the glue off. Done that plenty of times it works.
|
|
![]() |
![]() |
![]() ![]() |
|
Bookmarks |
|
|
![]() |