Broken mag spring(pull down part)

Flabeo · January 8th, 2006, 10:55

Im not sure what you actully call it but its broken I was firing the gun and it got cold when I slid it down to put more bbs in I let go by mistack and it snaped off. the gun is a Kjw glock 23 pictures of the mag are below. I was woundering if it was posible to buy a new part or do I have to get a new mag. if I can buy a new one where and how much might it be. Also does anyone know how possably open it up so i can replace it or make a modifaction to the broken one.
Picture 1
Picture 2

CDN_Stalker · January 8th, 2006, 11:25

Does the KJW Glock mags have the same type of baseplate that slides forward to expose the fill valve? If so, you can remove the plate completely and knock a pin out (KSC is like that) that you can pull out the spring base, spring and follower (that is the part you broke, the follower). A fix? Well, if you have access to small set screws and a tap/die set, you can drill a small hole in the follower, tap it for a #2-56 or #4-40 set screw that is short enough to sit in the groove without interferring with the action, that itself will give you purchase to pull the follower down to load the mags.

Kid · January 8th, 2006, 12:46

The valve on the KJ is exposed on the bottom. No sliding baseplate to show it. I've owned two of them.

Flabeo · January 8th, 2006, 15:35

so I can't open it the way he said. Thanks for the help CDN_Stalker. Another option is to buy a new mag but I havent seen anyone selling any.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

January 8th, 2006, 10:55	#1
Flabeo Trader rating Join Date: May 2005 Location: Halifax N.S.	Broken mag spring(pull down part) Im not sure what you actully call it but its broken I was firing the gun and it got cold when I slid it down to put more bbs in I let go by mistack and it snaped off. the gun is a Kjw glock 23 pictures of the mag are below. I was woundering if it was posible to buy a new part or do I have to get a new mag. if I can buy a new one where and how much might it be. Also does anyone know how possably open it up so i can replace it or make a modifaction to the broken one. Picture 1 Picture 2 __________________

January 8th, 2006, 11:25	#2
CDN_Stalker Official ASC Bladesmith Trader rating Join Date: Jul 2003 Location: Ottawa, Ont.	Does the KJW Glock mags have the same type of baseplate that slides forward to expose the fill valve? If so, you can remove the plate completely and knock a pin out (KSC is like that) that you can pull out the spring base, spring and follower (that is the part you broke, the follower). A fix? Well, if you have access to small set screws and a tap/die set, you can drill a small hole in the follower, tap it for a #2-56 or #4-40 set screw that is short enough to sit in the groove without interferring with the action, that itself will give you purchase to pull the follower down to load the mags. __________________ STKR Knives http://www.facebook.com/#!/pages/STK...17036668380871

January 8th, 2006, 12:46	#3
Kid Trader rating Join Date: Feb 2005 Location: Moose Jaw, SK	The valve on the KJ is exposed on the bottom. No sliding baseplate to show it. I've owned two of them.

January 8th, 2006, 15:35	#4
Flabeo Trader rating Join Date: May 2005 Location: Halifax N.S.	so I can't open it the way he said. Thanks for the help CDN_Stalker. Another option is to buy a new mag but I havent seen anyone selling any. __________________

Broken mag spring(pull down part)

Doctor's Corner