![]() |
|
|
||||||||
|
Home | Forums | Register | Gallery | FAQ | Calendar |
Retailers | Community | News/Info | International Retailers | IRC | Today's Posts |
![]() |
|
Thread Tools |
![]() |
#496 |
a.k.a. cloaked
|
Hey guys, there's a version 2 RA-TECH Stinger Hop Up for the WE M4s at WGC and no where else that I know of. Does anyone have one of these and know if there's any performance differences between the version 1 and version 2?
Here's a link to the Stinger Hop Up. |
![]() |
![]() |
![]() |
#497 |
Division
|
I meant to post this for a while now, I also had problems with the bolt catch once. I've been using this on my real steel upper for about 2 months and have had zero problems. I have not tested this with the WE upper but the dimensions seem the same.
This extra bit of metal pushes up against the wall of the upper and keeps the bolt catch from engaging fully. Only 1mm of the bolt catch face catches the bolt, eroding and smoothing the edge away. ![]() I grinded the extra bit of this off and now the extra spacing inside the receiver allows the catch to engage fully. ![]() ![]() ![]()
__________________
![]() Weee! Last edited by Qlong; October 22nd, 2010 at 00:40.. |
![]() |
![]() |
![]() |
#498 |
where can i get my hands on a we m4 part 092
__________________
:infantry: dont shoot till you see the whites of there eyes! |
|
![]() |
![]() |
![]() |
#499 |
Division
|
Go to our Canadian WE distributor. Velocity Arms.
__________________
![]() Weee! |
![]() |
![]() |
![]() |
#500 |
Does anyone have any links to animations or detailed description of how each part of a WE M4 works? Im looking for an animation or something I can see to learn about the internals.. please dont flame my ass..im planning to disassembly my M4 tomorrow to learn about it and Im looking for some guide.
|
|
![]() |
![]() |
![]() |
#501 |
Captain Sunshine
|
why don't you just sit down and try it out? its honestly not hard to find out what does what when you have it in half on your lap.
|
![]() |
![]() |
![]() |
#502 |
anybody know how to remove the trigger mechanism for the pdw cuz i want to switch them out for the ra tech parts
|
|
![]() |
![]() |
![]() |
#503 |
aka coachster
|
|
![]() |
![]() |
![]() |
#504 |
![]() |
![]() |
![]() |
#505 |
aka coachster
|
|
![]() |
![]() |
![]() |
#506 |
Hey guys, been having a reoccuring problem with my WE M14.
Sometimes when I shoot, the nozzle seems to get stuck half way on the return half of the firing cycle. And it jams there, hard. Sometimes it'll shoot fine, sometimes it wont. Normally after racking the bolt a few times it loosens back up but I dont think that is good for the rifle. Any idea what may be causing this, and the best solution to fix? Thanks. Last edited by Strelok; October 25th, 2010 at 19:28.. |
|
![]() |
![]() |
![]() |
#507 |
![]() |
![]() |
![]() |
#508 |
aka coachster
|
if you look closely, only one of the 3 pins actually can be punched out. once out, the plate slides off. can't remember for sure but I believe it slides backwards.
|
![]() |
![]() |
![]() |
#509 | |
Quote:
![]() here's whats left of the lower |
||
![]() |
![]() |
![]() |
#510 |
aka coachster
|
the pin directly above the trigger. remove that.
slide the rear body pin out and push out the piece that the selector switches attach to. remember to note the orientation of it and watch out for little bits that might fall or shot out. lol Last edited by coach; October 26th, 2010 at 20:09.. |
![]() |
![]() |
![]() ![]() |
|
Bookmarks |
|
|
![]() |