|
|
|
|
|
||||||||
|
|
|||||||||
| Home | Forums | Register | Gallery | FAQ | Calendar |
| Retailers | Community | News/Info | International Retailers | IRC | Today's Posts |
 |
|
|
Thread Tools |
January 9th, 2014, 15:39
|
#1 | |
|
Ak v3 gearbox, nozzle not always resetting
I have a Cybergun aks-74u with a LCT gearbox and I just replaced the nozzle with an aluminum one. I was trying it out and found it was sometimes double feeding and other times not feeding at all. So I cleared it all out and when looking down the feeding nozzle (with eye protection just in case, you can never be too careful you know) I found that the air nozzle wasn't always resetting all the way (it would reset in the halfway point and then after a few shots it would reset to the back).
Does anyone know what might be wrong? could it be the tappet plate or maybe the spring for the tappet plate? help!!
__________________
Current loadout: FN-FX45, G&G L85A2.  Quote:
|
|
|
|
|
January 9th, 2014, 16:48
|
#2 |
|
Squid Porn Superstar, I love the tentacles!
|
What you are describing sounds completely normal.
|
|
|
|
|
January 9th, 2014, 17:46
|
#3 | |
|
|
really?
Out of 3 AEG's I've owned, this is the first to do it
__________________
Current loadout: FN-FX45, G&G L85A2. Quote:
|
|
|
|
|
|
January 9th, 2014, 17:55
|
#4 |
|
Not Eye Safe, Pretty Boy Maximus on the field take his picture!
|
the position the nozzle stops in is relative to where the sector gear stopped spinning.
most likely its a bad air nozzle or you inadvertently created an air leak somewhere |
|
|
|
|
January 9th, 2014, 18:50
|
#5 |
|
Squid Porn Superstar, I love the tentacles!
|
What was the last thing you changed before it started misfeeding?
Yeah the usually doesn't usually stop in the full forward position after firing on semi unless you have a super slow rate of fire or really good AB. |
|
|
|
|
January 9th, 2014, 19:30
|
#6 | |
|
|
The last thing I changed was the air nozzle, so I highly doubt that it's "bad", though it's not impossible that it's leaking. Oh! and it was miss-feeding when I got the gun because of bad hop up bucking.
__________________
Current loadout: FN-FX45, G&G L85A2. Quote:
Last edited by Nateman332; January 9th, 2014 at 19:59.. |
|
|
|
|
|
January 9th, 2014, 20:06
|
#7 |
|
Not Eye Safe, Pretty Boy Maximus on the field take his picture!
|
can you chrono it?
ive seen air nozzle leaks accountable for 90fps drops and misfeeding |
|
|
|
|
January 9th, 2014, 20:25
|
#8 | |
|
|
Sadly, no, I can't crono it.... but I can tell it's not shooting the 400 FPS it's supposed to.
Is there anyway to seal up the nozzle without buying a new hopup unit?
__________________
Current loadout: FN-FX45, G&G L85A2. Quote:
Last edited by Nateman332; January 9th, 2014 at 20:33.. |
|
|
|
|
|
January 9th, 2014, 20:40
|
#9 |
|
Not Eye Safe, Pretty Boy Maximus on the field take his picture!
|
do a compression test on the mechbox with the nozzle in the forward position
|
|
|
|
|
January 9th, 2014, 22:05
|
#10 |
|
Banned
|
stupid question, is the feeding nozzle the same length as the last.
|
|
|
|
|
January 10th, 2014, 00:04
|
#11 |
|
Squid Porn Superstar, I love the tentacles!
|
Wait so when you say it was misfeeding because of a bad hop up, is that what you were told or did you confirm it by fixing it?
What tells you it should be shooting 400 fps? |
|
|
|
|
January 10th, 2014, 00:31
|
#12 | ||
|
|
Quote:
__________________
Current loadout: FN-FX45, G&G L85A2. Quote:
|
||
|
|
|
|
January 10th, 2014, 00:35
|
#13 | ||
|
|
Quote:
and I was told that it was shooting ~400 fps by the seller (who did have a crono)
__________________
Current loadout: FN-FX45, G&G L85A2. Quote:
|
||
|
|
|
|
January 10th, 2014, 01:13
|
#14 |
|
formerly steyr
|
Does the nozzle actually fit in the hopup unit?
|
|
|
|
|
January 10th, 2014, 02:34
|
#15 | ||
|
|
Quote:
If it does fit too loosely then does anyone have any ideas that don't require me buying a new hop up unit? I'm low enough on funds as it is.
__________________
Current loadout: FN-FX45, G&G L85A2. Quote:
|
||
|
|
|
 |
|
||||||
| Bookmarks |
|
|
 |
|
